HVAC Contractor in Chadds Ford, PA: Expert Comfort Engineering

I completed a voltage enhancement renovation on a York 2-ton R22 system. The initial inspection revealed significant wear and tear, typical for an older system. I began by thoroughly examining the entire system to identify areas requiring attention. After pinpointing the problematic components, I proceeded with the necessary repairs, ensuring all connections were secure and functioning correctly. I replaced any worn-out parts and optimized the system's voltage to enhance efficiency. Post-repair, I conducted a comprehensive test run to confirm the system's proper operation. The customer was informed about the system's age and condition but was reassured by the improvements made today. The system is now running smoothly.

Furnace Repairs: Swiftly responding to a reported malfunction in the furnace's inducer motor, our expert technician conducted a prompt and thorough examination. The diagnosis pinpointed a fault in the inducer motor, necessitating immediate attention. With precision and efficiency, we replaced the malfunctioning motor with a high-quality component. This meticulous replacement not only resolved the specific issue but also played a crucial role in ensuring proper ventilation throughout the system. By restoring efficient heating functionality, we provided the homeowner with a reliable and well-ventilated indoor environment, promoting comfort and peace of mind.

Found refrigerant leak at access port on evaporator coil suction line. Repaired leak. Adjusted refrigerant charge.

No A/C, GSX140361KH, 2208025548, no access to the indoor system, too off system so customer can use for now, need to return after the customer has got a access opening to the indoor system.

No A/C, GSX140361KH, 2208025548, no access to the indoor system, too off system so customer can use for now, need to return after the customer has got a access opening to the indoor system.

No A/C, GSX140361KH, 2208025548, no access to the indoor system, too off system so customer can use for now, need to return after the customer has got a access opening to the indoor system.

No A/C, GSX140361KH, 2208025548, no access to the indoor system, too off system so customer can use for now, need to return after the customer has got a access opening to the indoor system.

Free estimates.

The supply is 108 and the return is 80 with a heat rise of 28. Ignition is in good condition. Voltage enhancement system read 9.7 with a factory setting of 10 also Cleaned the fan blower . Heat exchanger are also in good condition

The supply is 108 and the return is 80 with a heat rise of 28. Ignition is in good condition. Voltage enhancement system read 9.7 with a factory setting of 10 also Cleaned the fan blower . Heat exchanger are also in good condition

The supply is 108 and the return is 80 with a heat rise of 28. Ignition is in good condition. Voltage enhancement system read 9.7 with a factory setting of 10 also Cleaned the fan blower . Heat exchanger are also in good condition

The supply is 108 and the return is 80 with a heat rise of 28. Ignition is in good condition. Voltage enhancement system read 9.7 with a factory setting of 10 also Cleaned the fan blower . Heat exchanger are also in good condition

Cooling Rejuvenation Outdoor unit voltage enhancement system read 5/43.7mfd with a factory setting of 5/45mfd and is within allowable fault. The FLA 0.6 and the RLA is 6.1. Cleaned outdoor coil and exterior, interior clear. Checked disconnect for safety. Indoor unit has a supply of 57 with a 75 return and 18 delta. Blower amps 4.9 and the voltage enhancement system read 9.9mfd with a factory setting of 10mfd and is within allowable fault. Board and connections good. Blower looks fine, spins without restriction. Indoor coil looks ok, as does pan. System normal operation at this time.

Cooling Rejuvenation Outdoor unit voltage enhancement system read 5/43.7mfd with a factory setting of 5/45mfd and is within allowable fault. The FLA 0.6 and the RLA is 6.1. Cleaned outdoor coil and exterior, interior clear. Checked disconnect for safety. Indoor unit has a supply of 57 with a 75 return and 18 delta. Blower amps 4.9 and the voltage enhancement system read 9.9mfd with a factory setting of 10mfd and is within allowable fault. Board and connections good. Blower looks fine, spins without restriction. Indoor coil looks ok, as does pan. System normal operation at this time.

Cooling Rejuvenation Outdoor unit voltage enhancement system read 5/43.7mfd with a factory setting of 5/45mfd and is within allowable fault. The FLA 0.6 and the RLA is 6.1. Cleaned outdoor coil and exterior, interior clear. Checked disconnect for safety. Indoor unit has a supply of 57 with a 75 return and 18 delta. Blower amps 4.9 and the voltage enhancement system read 9.9mfd with a factory setting of 10mfd and is within allowable fault. Board and connections good. Blower looks fine, spins without restriction. Indoor coil looks ok, as does pan. System normal operation at this time.

Cooling Rejuvenation Outdoor unit voltage enhancement system read 5/43.7mfd with a factory setting of 5/45mfd and is within allowable fault. The FLA 0.6 and the RLA is 6.1. Cleaned outdoor coil and exterior, interior clear. Checked disconnect for safety. Indoor unit has a supply of 57 with a 75 return and 18 delta. Blower amps 4.9 and the voltage enhancement system read 9.9mfd with a factory setting of 10mfd and is within allowable fault. Board and connections good. Blower looks fine, spins without restriction. Indoor coil looks ok, as does pan. System normal operation at this time.

80% 60k furnace and 14 SEER 2 ton AC